This is a coverage map of WZCO-FM 89.9. Anywhere you see color on the map, there is a usable signal. We are at full power.WZCO_FM_LUFactors Affecting Reception

FM radio waves can be affected by many factors ranging from terrain to equipment. In general, FM transmissions are lines of sight — similar to light waves. WZCO’s 25,000 watts are transmitted from a cell tower in Clarkton. Unless an object (building, ridge etc) is between you and Clarkton, you should have clear reception up to 50 miles from the transmitter. After 50 miles, reception becomes a factor of the strength of the signal, as much as your location in relation to the transmitter. In these cases, terrain and equipment are major players.

Following are some suggestions for improving home reception through the addition or adjustment of receiving antennas. These methods may or may not work, but improving your antenna is the single best solution to reception problems (short of moving or installing a translator). The solutions offered here range from things you can do for free, to equipment you can purchase. We are not selling equipment, just passing along tidbits of verified reception lore for your listening pleasure.

Antennas: Some General Concepts

  • An antenna is a “collector” of radio signals that improves your reception by providing more signal than would be otherwise supplied to the receiver.
  • An outdoor antenna is preferable to an indoor antenna.
  • A high location is better, whether it be the roof, a hill out back, or the top shelf of a bookcase.
  • Because WZCO is vertically polarized, the more vertical the antenna, the better.
  • Many things in a house can affect reception, so as a first step, try your radio or antenna in different spots in the house.
  • YOU are an antenna! If you improve reception by standing near or touching the radio or antenna, your system is telling you it needs a better antenna.
  • A rotorized (pointable) antenna is preferable to a stationary antenna. A fixed-position FM antenna should be pointed toward Clarkton.

Your Radio

Determine whether or not your radio has antenna terminals for attachment of an antenna. These would appear as:

  • Screws on the back labeled “ant. 300 ohms” or
  • A coaxial cable connector labeled “coax/ant. 50 ohms” (W=ohms)

Otherwise, your radio has either an internal antenna that you can’t see or a telescoping antenna. Either way, skip ahead to the section “No Antenna Terminals.”

Connecting an Antenna to Your Radio

There are two different types of antenna cable, flat two-conductor wire known as “twin lead” that is 300W, or round plastic coated wire that is known as “coaxial” or “coax” that is 50-75W. Coax is what cable companies use, and is a much better cable, but it is more expensive. You’ll have to decide which to use if you are installing a new antenna or cable. Other than conducting a stronger signal, coax is useful in situations requiring the elimination of interference cause by nearby electric motors, computers, etc. We’d be glad to advise you.

If you have a TV antenna already installed, purchase a “FM Splitter” at a radio supply store. Follow the instructions, hooking up the “FM output” of the splitter to the radio and using the “TV output” to restore the connection to your TV. Experiment attaching wires to one screw and then the other to see what gets the best reception; the only rule is “do whatever works best”.

If you receive your TV signal via a cable system and your TV antenna is unused, then just hook it up to your antenna terminals on the radio and you should have dramatically better reception.

If you are still experiencing reception problems after connecting an antenna, try aiming your antenna directly at Clarkton. If aiming the antenna at Blue Hill Mountain causes reception problems with other TV or radio stations, consider:

  • installing a motorized rotor to move your antenna from inside,
  • dedicating an FM antenna to permanently point to Clarkton
  • dreaming up some unique arrangement allowing for pointing the antenna, like the one described in the last section, “Other Ideas”.

Using a Di-Pole Antenna

Di-poles are T-shaped wire antennas made for indoor use. You can buy them in radio supply stores, and they are inexpensive.

Attach the bottom leg of the T to the antenna terminals of your radio (experiment while attaching) and then play with the location of the T. The placement of the T is critical to the performance of the di-pole.

If you are really bold, or crave WZCO reception on a budget, you can make a custom di-pole. The advantage is that you can greatly increase a di-pole’s effectiveness by its size and/or placement outside! You’ll need some of the twin lead cable we mentioned earlier.

The custom di-pole you make will be a T just like the ready-made you might buy, except you’ll be able to tailor it to your needs. However, you need to abide by these, or multiples of these, dimensions; the top bar should be 5’1″ or 10’2″ or 15’3″ or 20’4″, etc. and the bottom leg must connect at the middle of that top bar (2’6″, etc.) You can drape custom di-pole over the roof of your house, or climb the tree in your front yard and tie it to the appropriate branches (of course, experimenting tirelessly to find the proper orientation of the di-pole for best reception). Twin lead is so cheap that you may find yourself quite proud of the dramatic improvement in reception for a bit of time, but very little money. However, don’t kid yourself about the effectiveness of a custom di-pole versus a traditional metal TV/FM antenna.

Cut an appropriate length of twin for the top bar. In the middle of that length cut one of the two conductors and strip back the plastic coating. Now connect another length of the twin lead to the two bare conductors of the top bar. The other end is connected to your radio antenna terminals.

If a custom di-pole sounds like too much trouble, you can make a cut-and-split di-pole. Take some twin lead and split it down the middle. Attach the other end to the radio. Very simple, though not as effective as the custom di-pole.

No Antenna Available? Make a Wire Antenna

Homemade antennas can work very well. Often a piece of wire becomes an antenna without much fuss at all. It can be thick or thin wire, and free or cheap is the best wire around. Wire with a plastic coating is safer (remember to strip any coating away to allow connection of the wire to the antenna terminals), but bare wire is fine.

Use any piece of wire. Attach it to an antenna terminal. Run it over drapery rods and window casings. Throw it out the window and into the nearby tree. Toss it onto the roof. Do the same with two wires. Spend some time experimenting with the placement of these wires; often opposite directions work well. If this is strictly an inside job make sure that you arrange these wires so that you’ll be proud to point them out to visitors. “See my antenna; I get WERU loud and clear!”

No Antenna Terminals

Clock radios normally don’t have any antenna terminals or telescoping antennas. Try wrapping lots of wire around the radio; don’t connect the wire to anything. The idea is to get a thick loop of wire near the radio.

Almost any large metal structure above ground can act as antenna. Aluminum rain gutters, air conditioning and heat ducts, metal window frames, aluminum siding and metal roofing are great antennas. NEVER USE an electrical outlet as an antenna. using an alligator clip, clip to one of these the previously mentioned massive loop of wire surrounding your clock radio. Wow!

Other portable-type radios have telescoping antennas that may be improved by wrapping a “flag” of aluminum foil around the top, or attaching a length of wire to the telescoping antenna. That length of wire might get thrown in the tree next to your garden as your are gardening and listening to the radio, or more permanently attached to the rain gutter outside your bedroom window, or tossed on the roof.

Other Ideas

  1. Rabbit ears are cheap. Strap them to your chimney, or climb a tree and place them carefully according to the reception data your friend yells out the window to you. Rabbit ears are not intended to be placed outside, as they will deteriorate to the point of uselessness. But, in our experience this happens only after many years. Or try putting them in your attic.
  2. Select MONO on your receiver. For reasons beyond the scope of this pamphlet, MONO signals travel farther and have less noise in them.
  3. Buy a booster or amplifier for your existing antenna. Sometimes they work wonders, sometimes they just work. Boosters need a certain amount of signal to work with, otherwise they end up amplifying noise rather than audio.
  4. Here is an “attic solution” offered by a listener of KSER near Seattle: “I installed a radio-TV antenna (a.k.a. yagi) in my attic. I have some string attached to it and can rotate it from a closet near the radio. I can position it for KSER or various TV stations. The vertical rod is a broomstick. I get about 90 degrees rotation. The advantage is that I’ve eliminated the expenses of mounting the antenna outdoors and a rotor, but I still have it in a relatively high place and can position it easily.”

Build Your Own Antenna Tuned to WERU

WERU has detailed plans for building your own antenna tuned specifically to WERU. In very fringe areas this antenna would provide significant improvement in reception. Another useful application of this antenna would be if you are experiencing interference from another station while trying to tune WERU.

Here are the antenna plans (PDF format, 160 KB file size), and important notes about building such an antenna appear below. Special thanks to Jack Dice and Mark Roman for the plans and notes.

Design Notes:

  • The critical dimensions (the lengths of the antenna elements and the spacing of them) were calculated using a formula obtained from an article in Popular Science circa 1956. A neighbor’s grandfather had snipped it out and saved it. He and I have both built antennas to receive WERU and we get very good reception.
  • The variable in the formula is radio frequency. The frequency is multiplied by constants to determine the lengths and spacings of the antenna elements. The design presented here is dimensioned to receive 89.9 mHz, the broadcasting frequency of WERU.
  • The framing design is one that I came up with. It is especially good when using a “donor” antenna (explained later) that requires the elements to be joined together in the center of their span and that need support on each side of the joint. Actually, any fixture will work as long as the structure holds the antenna elements in alignment in the same plane and is able to withstand the abuse of being up on a roof throughout the weather extremes we have here in Maine.

Construction Notes:

  • For the stringers, choose straight grained wood with no large knots that span the thickness of the stringer. These would weaken it.
  • I have given an actual dimension of ¾” by 2″ by 13′ for the two stringers. To get these dimensions will require ripping a “one by” down to 2″ width. If you do not have the capability to rip a long piece of wood, choose wood as close as you can get to 2″ from the lumber yard. Strapping is usually available in “1 by 3” (actual dimension ¾” by 2 ½”). It is often not of the best quality wood so make sure it is reasonably straight and there are no large knots in it. I would not recommend using narrower than ¾” by 2″ wood for the stringers.
  • The spacer dimensions and numbers are not critical. Use your scraps to space the two stringers apart and hold them together.
  • The ideal location for the mast mount is on the balance point of the fully assembled antenna. The geometric center (6′ 6″ from the end of the stringers) will be close enough if you want to plan for the mount before assembling the whole unit.
  • The dimensions calculated by the formula are given in the drawing as decimal inches. I have converted these to the nearest 1/16″ as indicated by the parentheses. When constructing the antenna, be as careful as you can to obtain the dimensions given.

Purchase a Custom-made Antenna

Directive Systems, a small antenna manufacturing company in southwest Maine, produces an antenna that some listeners may find to be a worthwhile investment. For more information contact David Olean at RR#2 Box 282, Dixon Rd., Lebanon, ME 04027 or 207-658-7758.


Thanks to WERU for this great info!

Leave a Reply